How to set up a protein skimmer
How an in-sump or internal protein skimmer is sized, installed, and tuned, using Simplicity’s and Sicce’s published directions.
A protein skimmer removes dissolved organic waste from a saltwater tank by making a fine foam and lifting that waste into a collection cup. This guide follows Simplicity’s published assembly, sump-depth, and tuning directions for the DC in-sump skimmers, and Sicce’s published sizing and use directions for the Shark internal skimmers.
Quick size picker: which skimmer for your tank?
Medium-bioload tank sizes from each maker’s published chart (details for light and heavy bioloads are further down).
| Tank (medium bioload) | Skimmer | Style |
|---|---|---|
| Up to 25 gal | Sicce Shark 150 | Internal (display, all-in-one back chamber or filter compartment) |
| Up to 50 gal | Sicce Shark 300 | Internal |
| Up to 90 gal | Simplicity 120DC | In-sump, DC controller |
| Up to 180 gal | Simplicity 240DC | In-sump, DC controller |
| Up to 240 gal | Simplicity 320DC | In-sump, DC controller |
| Up to 600 gal | Simplicity 800DC | In-sump, DC controller |
Heavy feeders or a packed tank? Use the lower heavy-bioload figures below. See all protein skimmers.
What you’ll need
an in-sump skimmer with a controller, in 120DC, 240DC, 320DC, and 800DC sizes (the 540DC size was sold out when this was written)
From $259.95
Choose size
a compact internal skimmer for a display, an all-in-one back chamber, or a filter compartment, in 150 and 300 sizes
From $149.99
Choose size
a surface skimmer for oily film; it is not a protein skimmer, but it helps keep the surface clear
From $42.99
Choose sizeA protein skimmer does not replace a finished cycle, regular water changes, or testing. See Cycling a new tank and Testing your water. For a first nano list, see Nano reef equipment list.
Which style fits the tank
In-sump skimmers, such as the Simplicity DC line, sit in a sump and cover a wide range of tank volumes. Internal skimmers, such as the Sicce Shark, go in the display or a tight filter compartment and are aimed at smaller volumes. Pick the style that matches the space and a stable water level you actually have, then size it from the maker’s chart.
Simplicity DC: official tank size and water depth
From Simplicity’s published model comparison (light / medium / heavy bioload):
Simplicity DC skimmerView product →
- 120DC — up to 120 / 90 / 60 gallons
- 240DC — up to 240 / 180 / 120 gallons
- 320DC — up to 320 / 240 / 160 gallons
- 540DC — up to 540 / 405 / 270 gallons (this size was sold out here when this was written)
- 800DC — up to 800 / 600 / 400 gallons
Simplicity’s current assembly guide lists these sump water depths for best performance: 6–8 inches on the 120DC and 240DC, 7–9 inches on the 320DC, and 8–10 inches on the 540DC and 800DC. If the skimmer section is too deep, Simplicity says to raise the skimmer or adjust the sump baffles so the water sits in that range.
How to assemble and install a Simplicity DC skimmer
From Simplicity’s assembly guide:
- Inspect the parts before you start: collection cup and lid, wedge pipe, bayonet neck, bubble plate and lid, pump, air-intake adjustment, air silencer, airline, and venturi.
- Mount the pump and bubble plate. Remove the four white thumb screws and lift off the body. Slide the pump onto the base plate (Simplicity notes the fit is tight to reduce vibration). Fit the bubble plate and retaining nut, then the bubble plate lid with the nylon screw, oriented so the section without holes sits above the pump output. Route the pump cable into the base slot, slide the body back on so the hole lines up with the pump intake, and replace the thumb screws.
- Assemble the air intake. Attach the air silencer to the standpipe with the white nylon screw, connect the airline from the silencer to the venturi, and insert the venturi into the pump intake.
- Place it in the sump, in the water, after mechanical filtration. Simplicity specifies in-sump / in-water installation only, after a filter sock or other mechanical filter, and recommends foam or filter floss after the skimmer to catch stray bubbles.
- Connect the controller and power supply in a cool, dry place. Simplicity says not to place the power supply on the floor or near the sump. Then plug it in.
How Simplicity says to tune it
From Simplicity’s tuning guide and FAQ:
- Open the wedge pipe fully (arrow to notch).
- Run the pump at full speed unless the wedge is already fully open and the cup is filling quickly with water. In that case, Simplicity says to reduce pump speed.
- Set the air valve. Close the air-intake screw completely, then open it about half a turn until you have a dense air-water mix. Simplicity notes that smaller bubbles are better, and that reducing airflow can produce smaller bubbles and pull in more air. Wait 30–60 seconds between small changes.
- Raise the water in the body slowly by closing the wedge pipe until the bubbles reach the bottom of the neck. Wait 1–2 minutes and adjust again if needed. After 15–30 minutes you should see larger bubbles at the top of the column. After 1–2 hours, the foam should begin to rise into the cup.
- Judge the skimmate, not the clock. Simplicity’s target is brown waste similar to dark-brewed tea. If the waste is very light, open the wedge slightly. If you barely collect anything, close it slightly. When you add foods, medications, or supplements that change bubble production, Simplicity says to slow or turn the skimmer off so you do not have to retune it afterward.
Sicce Shark: official size and how to use it
From Sicce’s Shark instruction manual and product pages:
Sicce Shark skimmerView product →
- Shark 150 — up to 40 US gallons (150 L) low bioload, 25 gallons (100 L) medium, or 13 gallons (50 L) high; about 40 gph (150 L/h) of air; 4 W; diffusion-surface skimming.
- Shark 300 — up to 80 US gallons (300 L) low bioload, 50 gallons (200 L) medium, or 25 gallons (100 L) high; about 45 gph (180 L/h) of air; 5 W; counter-current skimming with an adjustable water entrance; ozone-compatible.
- Both models: immersion depth 5–6 inches (130–150 mm); magnetic holder for glass up to 15 mm (0.6 inch); cup volumes 170 ml (150) and 260 ml (300). Use only submerged, and only in water or surroundings not above 95 °F (35 °C). Do not run it dry.
- Place it in a corner, or in a filter compartment with a constant water level. Bring the outer magnet to the glass until it holds. Sicce says the water should match the LEVEL mark on the left side of the skimmer, and they recommend an auto top-off to keep that level steady — see How to set up an aquarium auto top-off. Keep it away from a circulation pump, which Sicce says can disturb the internal flow.
- Start with the air silencer fully open so bubbles rise in the bottom of the reactor. A new skimmer may take a few days before it really starts to skim.
- Make only small height or air changes, then wait. If skimming is too wet (the cup fills quickly with very light waste), restrict the air or raise the skimmer so the LEVEL line sits slightly above the water. If it is too dry, keep the air fully open or lower the skimmer so the LEVEL line sits slightly below the water. Sicce says normal operation uses maximum air flow. On the 300, you can also lift or lower the front water entrance; they caution that a wrong setting reduces sensitivity.
- Empty the cup regularly. Always unplug the skimmer first. Sicce notes that pulling the cup also rinses the internal air hose and nozzle. Clean the cup with water and the included brush, reinstall it, and switch the pump back on. Check and clean the air-control silencer each week.
The Shark 300 can be used with ozone only with the fittings and limits in Sicce’s manual, including their 1 mg of ozone per 100 liters figure if you use ozone at all. Skip that add-on unless you have the right equipment and have read that section. Uncontrolled ozone use can be harmful.
Surface film is a different job
A protein skimmer pulls dissolved waste out of the water column. A surface skimmer, such as the Sicce Shark Mini Skim, removes the oily film that can sit on the surface. You can use both. Do not expect one to replace the other.
Good habits
- Give a new skimmer time. Both makers describe a start-up period of hours to a few days.
- Keep the cup and air path clean. Performance drops when the impeller, silencer, or air line is dirty.
- Watch salinity when you skim wet. A wet cup removes more water, which an auto top-off will replace with fresh RO/DI.
For help choosing flow in the display, see Choosing a return pump or wave pump.
Orders ship in 1–2 business days, and shipping is free on orders of $35 or more. Most equipment is returnable for 365 days with free return shipping and no restocking fee. Opened chemicals, foods and medications are not returnable.
If you want help matching a skimmer size to your tank and sump depth, ask us through the contact form.