How to lower ammonia in a fish tank
Short answer: Test first. Any detectable ammonia is a problem — Fritz says the target is always 0 ppm. Then do three things: a water change sized to the reading, a conditioner that detoxifies ammonia (such as Seachem Prime or Fritz Complete), and nitrifying bacteria to rebuild the filter. Conditioners bind ammonia so it is less toxic; they do not remove it. The bacteria do that over time. Use the amounts on the label; the figures below are the manufacturers' published directions.
Test before you dose
You cannot see ammonia. Use a kit, write the number down, then act. Three options we carry:
| Kit | What the maker states |
|---|---|
| Fritz Ammonia Test Kit | Liquid reagent kit that measures total ammonia in fresh and saltwater, about 130 tests. Fritz recommends a salicylate-type kit (yellow/green chart) like this one if you are also using Fritz Complete; Nessler-type (yellow/amber) kits will not be accurate with that conditioner. |
| Seachem MultiTest: Ammonia | Measures both total and free (toxic) ammonia to below 0.05 mg/L, about 75 tests, with a reference solution. Seachem says this gas-exchange kit is not affected by Prime or similar binders. |
| Seachem Ammonia Alert | A sensor disc that stays in the tank and changes color to show free ammonia continuously, with no reagents. |
See the rest in our test kits collection, and read which test kits you need.
What the reading means
Fritz states that the ideal ammonia level is always 0 ppm, and that any detectable amount is a concern. Fritz also notes that ammonia exists as toxic NH3 and less-toxic NH4+ (ammonium), and that higher pH and higher temperature shift the balance toward the more toxic form. Seachem similarly distinguishes free ammonia from total ammonia, which is why MultiTest and Ammonia Alert report free ammonia.
Fish under ammonia stress may show rapid gill movement or clamped fins, according to Fritz. If a fish is sick or dies, Fritz says to test ammonia right away.
What to do right now
From Fritz's ammonia guide, after you complete the water-change and cleaning steps for the reading you have, add an ammonia remover such as Fritz Complete, then add nitrifying bacteria (FritzZyme 7 in freshwater or FritzZyme 9 in saltwater):
| Total ammonia | Fritz's published action |
|---|---|
| 0.5–1 ppm | Reduce feeding, clean the filter, and siphon the substrate |
| 2–3 ppm | Stop feeding temporarily and perform a 25% water change. Clean the filter and siphon the substrate |
| 4–5 ppm | Perform a 50% water change and follow the steps above. Consult your local aquarium dealer to help find the cause |
| 6–7 ppm | Perform a 75% water change, follow the steps above, and consult your local aquarium dealer right away. Fritz calls ammonia above 6 ppm a critical emergency |
Treat new tap water with a conditioner before it goes in, and match temperature as you would for any water change. Our guide to how to do an aquarium water change covers that process. Rinse filter media in a bucket of tank water, not tap water, so chlorine does not kill the bacteria you still have.
Detoxify the ammonia that is still in the tank
A water change dilutes ammonia. A conditioner binds what remains so it is less harmful while the biofilter catches up. Seachem is explicit: Prime does not remove ammonia, nitrite or nitrate; it binds them so they are harmless to livestock and still available to bacteria. Fritz says the same of Complete, and that it will not harm the biological filter.
| Product | Official amount | Notes from the maker |
|---|---|---|
| Seachem Prime | 1 capful (5 mL) per 200 L (50 US gallons) of new water, or on aquarium volume if you dose the tank directly | Detoxifies ammonia, nitrite and nitrate, and removes chlorine and chloramine, in fresh and saltwater. May be used during cycling. Seachem says Prime can be dosed every 24–48 hours, binds those compounds for up to 48 hours, and that if ammonia or nitrite is above 2 ppm you may use up to 5 times the normal dose. If temperature is above 30 °C (86 °F) and chlorine or ammonia are low, use a half dose. Full directions are in how to use Seachem Prime. |
| Fritz Complete | 1 tsp (5 mL) per 50 US gallons (189 L) | Detoxifies chlorine, chloramine, ammonia, nitrite, nitrate and heavy metals in fresh and saltwater, and will not affect pH or over-activate skimmers. Each dose neutralizes up to 0.5 ppm ammonia, 1.0 ppm nitrite and 15 ppm nitrate. For very high ammonia, Fritz says the dose may be increased or repeated up to 5 times within 24 hours. If you add more than one dose above 86 °F (30 °C), keep the water well oxygenated, because large amounts can reduce dissolved oxygen. |
If you dose Prime and then test immediately, many kits will still show ammonia. Seachem explains that Nessler kits give a false muddy-brown reading with Prime, and salicylate kits can break the Prime-ammonia complex and also give a false reading unless you read them right away. MultiTest Ammonia is the kit Seachem recommends in that situation.
Rebuild the biofilter
Binding ammonia is temporary. The long-term fix is nitrifying bacteria in the filter, which convert ammonia to nitrite and then nitrate. That is the same process as cycling a new tank; see cycling a new tank.
| Product | Water | Official starting use |
|---|---|---|
| Seachem Stability | Fresh and salt | Shake well. Turn off UV and ozone. New aquarium: 1 capful (5 mL) per 10 US gallons (40 L) on day 1, then 1 capful per 20 US gallons (80 L) daily for 7 days. Fish may be added during those 7 days if you keep dosing. Ongoing: 1 capful per 20 US gallons once a month or with each water change, and when adding fish or medicating. Keep UV and ozone off for the 7 dosing days, or at least 24 hours for later additions. Seachem says Stability is harmless if you use more than the label. |
| FritzZyme 7 | Freshwater | Live freshwater nitrifying bacteria to seed the filter, speed cycling, and re-establish bacteria after cleaning or medication. Follow the dose on the label for your tank volume. |
| FritzZyme 9 | Saltwater | Remove chlorine and chloramine first. Shake well and add directly to the aquarium. Turn off UV sterilizers before dosing and for 4 days after. New system: 4 oz (119 mL) per 5 US gallons (19 L); Fritz says repeat dosing is not required and that the dose may be increased up to 10 times for faster cycling or heavier stocking. Add livestock within 24 hours, do not overstock or overfeed, and check ammonia and nitrite daily. Maintenance: 1 oz (30 mL) per 5 US gallons as needed (new livestock, media changes, after medications). Store cool and dark; do not freeze or overheat; use before the expiration date. |
More conditioners and bacteria are in our water care collection.
Keep it from coming back
Once ammonia is at 0 ppm, keep it there. Don't overfeed. Do regular partial water changes, and rinse filter media only in tank water. After medications or a big filter change, add bacteria again using the maintenance doses above. If the tank was never fully cycled, stay on the cycling plan until ammonia and nitrite both read zero.
FAQ
Why does my test still show ammonia after I dosed Prime?
Seachem says Prime binds ammonia; it does not make it disappear from every test kit. Nessler kits will read wrong. Salicylate kits can also give a false ammonia reading unless you read them immediately. Use MultiTest Ammonia, or wait — Seachem says Prime dissipates from the system within 24 hours, and that you can re-dose every 24 hours if ammonia is still rising.
Will a conditioner starve my bacteria?
No, according to both makers. Seachem says Prime does not remove ammonia from the system; the bound form is still available to the biofilter. Fritz says the same of Complete, and that it will not harm biological filter beds.
Is this the same as cycling a new tank?
The bacteria are the same. A spike in an established tank is usually overfeeding, a skipped water change, or a filter cleaned too hard or knocked back by medication. A tank that never finished cycling still needs the full process in cycling a new tank, plus the emergency steps above until the numbers are down.