How to set up a hang-on-back aquarium filter

Seachem’s official Tidal hang-on-back setup, media layering, and maintenance, with size and flow figures from Seachem.

A hang-on-back (HOB) filter hangs on the rim of the tank, pulls water up into a media basket, and returns it over an overflow. This guide follows Seachem’s published Tidal™ product pages and the official Tidal 55 / 75 / 110 owner’s manual for setup, media layering, startup, and cleaning. Seachem also rates a Tidal 35; that model’s published feature list is a little shorter, and those differences are noted below. For a broader look at mechanical, biological, and chemical media, see Choosing filter media.

Quick answer: which Seachem Tidal size do I need?

Seachem rates each Tidal by the largest tank it is made for. Pick the size at or above your tank’s gallons. Figures are from Seachem’s published Tidal specs (the full details, including the wall clearance behind the tank, are further down).

Your tank Tidal model Flow Media volume Watts (120 V)
Up to 35 gal Tidal 35 130 GPH 0.2 gal 6 W
Up to 55 gal Tidal 55 250 GPH 0.32 gal 6 W
Up to 75 gal Tidal 75 350 GPH 0.50 gal 8 W
Up to 110 gal Tidal 110 450 GPH 0.85 gal 12 W

Tidal 55, 75 and 110 add a telescoping intake, an intake-regulation dial and a heater holder that Seachem doesn’t list for the Tidal 35. All four are rated for freshwater and saltwater. Shop: Seachem Tidal Power Filter · Tidal Matrix refill · Tidal foam insert · All filtration.

What you’ll need

Seachem Tidal Power Filter
Seachem Tidal Power Filter

the hang-on-back filter this guide is about, in 35, 55, 75, or 110

From $48.01

Choose size
Seachem Tidal Foam Insert
Seachem Tidal Foam Insert

the mechanical foam that sits at the bottom of the basket; a foam insert also ships with the filter

From $5.58

Choose size
Seachem Tidal Matrix
Seachem Tidal Matrix

a pre-measured bag of Matrix™ bio-media sized for your Tidal model; Matrix also ships with the filter

From $6.08

Choose size
Seachem Tidal Matrix Carbon
Seachem Tidal Matrix Carbon

pre-bagged MatrixCarbon™ sized for Tidal, if you want chemical filtration in the middle layer

From $6.91

Choose size
Seachem Tidal Polishing Pad
Seachem Tidal Polishing Pad

Seachem’s fine polishing pad, if you want an extra mechanical layer for fine particles

From $5.10

Choose size
Seachem Stability
Seachem Stability

only if you follow Seachem’s recommendation to add it when seeding new Matrix

From $3.45

Choose size

You will also need a grounded outlet on a GFCI-protected circuit, room behind the tank for the filter body, and a filled aquarium before you plug the filter in. Unplug the filter before any maintenance. Do not use soap or detergent on media or the impeller.

Pick a Tidal size

These aquarium-size, flow, wattage (120 V / 60 Hz), and filter-volume figures are from Seachem’s current Tidal product pages. Flow is Seachem’s published rate, not a promise of what your tank will measure after media is installed.Seachem Tidal Power Filter Tidal 35Seachem Tidal Power FilterView product →

  • Tidal 35 — aquariums up to 35 US gallons (130 L); 130 US GPH (500 L/H); 6 W; filter volume 0.2 US gallons (0.7 L). Wall clearance 2¾ in (7 cm); tank-trim clearance 13/16 in (2 cm); internal tank clearance 1⅜ in (3.5 cm).
  • Tidal 55 — up to 55 US gallons (200 L); 250 US GPH (1000 L/H); 6 W; filter volume 0.32 US gallons (1.2 L). Wall clearance 3 in (7.5 cm); tank-trim clearance 1 in (2.6 cm); internal tank clearance 1 11/16 in (4.3 cm).
  • Tidal 75 — up to 75 US gallons (300 L); 350 US GPH (1500 L/H); 8 W; filter volume 0.50 US gallons (1.9 L). Wall clearance 3½ in (8.5 cm); tank-trim clearance 1 5/16 in (3.3 cm); internal tank clearance 1¾ in (4.3 cm).
  • Tidal 110 — up to 110 US gallons (400 L); 450 US GPH (2000 L/H); 12 W; filter volume 0.85 US gallons (3.2 L). Wall clearance 4 in (9.5 cm); tank-trim clearance 1⅜ in (3.5 cm); internal tank clearance 2 in (5 cm).

No room behind the tank, or a tank over 110 gallons? If the wall clearance above won’t fit, the Sicce Shark PRO internal filter sits inside the tank instead (132, 185 and 238 gph models). For bigger tanks, the Sicce Mega Filtra canister filter comes in models for tanks up to 170, 240 or 250 gallons.

Seachem rates Tidal for freshwater and saltwater. The self-cleaning impeller is described as corrosion-resistant for both. A 3-year warranty covers defects in materials and workmanship from the date of purchase, except the pump’s impeller; Seachem says you can extend that to 5 years by registering the filter.

Tidal 55, 75, and 110 include a telescoping intake, a dual intake-regulation dial (surface skimmer versus the underwater intake), a leveling dial, and a heater holder. Seachem’s Tidal 35 feature and package list includes the surface skimmer, sub-surface intake, flow regulation, leveling dial, self-priming pump, foam, and Matrix, but it does not list a telescoping intake, a dual intake-regulation dial, or a heater holder. Use the 55 / 75 / 110 steps below only for those parts if your model includes them, and follow the sheet packed with a Tidal 35 for that model’s intake assembly.

How to hang and start a Tidal 55, 75, or 110

From Seachem’s official Tidal 55 / 75 / 110 owner’s manual. Read the safety section in that manual before you start: use a drip loop in the cord, a GFCI-protected outlet, and indoor use only. Seachem’s maximum stated liquid or environment temperature for the filter is 35°C / 95°F. Never run the pump dry.

  1. Assemble the telescoping intake if your model has one. Insert the bottom half of the tube into the top half, then seat the tube on the pump case.
  2. Install the heater holder only if you want a heater on the filter. Press the sides of the filter, pull down to remove the pump housing, slide the holder into the bottom of the housing facing up or down, route the pump cable into the guides, and replace the housing.
  3. Screw the leveling dial into the bottom of the filter housing. Hang the filter on the aquarium edge and turn the dial until the filter sits level.
  4. Route the pump cord through the guides and to the outlet, with a drip loop below the level of the receptacle.
  5. Fill the media basket before you plug the filter in. Remove media from plastic bags. Thoroughly rinse the foam and all media under running water. Layer from bottom to top: the foam filter (mechanical), then any chemical media such as MatrixCarbon™, then the Matrix™ biological media on top. Do not take Matrix out of its mesh bag. The bag is packed folded; lay it lengthwise and spread the media evenly. Do not overfill the basket — Seachem says overfilling can trip the maintenance alert or cause dripping from the right side of the return flow wall.
  6. Start the filter on a filled aquarium. Plug it in. The pump is self-priming and Seachem says it will begin filtering immediately. Keep the tank water at or above the “Minimum Water Level” mark on the filter so the pump does not run dry. There is no published maximum water level; Seachem recommends not going above the height of the surface-skimmer slots.
  7. Set the three adjustments (on models that have them): raise or lower the telescoping intake; set total flow with the front dial (Seachem says this can reduce intake flow by up to 80% while the motor stays in use, and the refiltration grid then recirculates water through the media for more contact time); and balance surface-skimmer flow versus the underwater intake with the side dial.

Seachem’s manual also says that, to seed new Matrix with bacteria more quickly, you can add Seachem Stability to the aquarium. Use the dose on Seachem’s Stability label; this guide does not repeat that bottle dose.

How to layer media

The official layering, bottom to top, is mechanical foam, then chemical media, then biological Matrix.Seachem Tidal Matrix Carbon Tidal 35Seachem Tidal Matrix CarbonView product →

Tidal Matrix Carbon is Seachem’s pre-bagged MatrixCarbon sized for each Tidal model, which the manual calls a preferred chemical option in almost any aquarium. Tidal Matrix is the matching pre-measured Matrix refill. A Tidal Polishing Pad is Seachem’s fine pad for capturing fine particles; if you add one, keep the basket from being overfilled and keep foam at the bottom so water still has to pass through the mechanical layer first. If you also run Seachem Purigen or Seachem PhosGuard as chemical media, follow those product directions — including Seachem’s note that PhosGuard should not tumble. See How to use Seachem Purigen.

When and how to clean it

Unplug the filter first. When the blue maintenance-alert float rises about ½ inch (1 cm) above the cover, Seachem says it is time to clean the basket. If water drips from the right side of the return flow wall, the basket is completely clogged and needs a thorough cleaning.

  1. Open the cover, slide the blue basket lock forward, and lift the basket out by the two side handles.
  2. Turn the cover over and set the basket into the slots on the cover so you can carry it without dripping.
  3. Take out the Matrix bag, any chemical media, and the foam. Rinse the foam thoroughly with water only — no soaps or detergents. Rinse or replace chemical media as that media’s directions require. Rinse Matrix gently in a container of tank water so it does not dry out. If you replace Matrix, Seachem says to replace no more than half of it at a time so you keep some of the existing bacteria; the manual suggests reseeding with Stability at that point.
  4. Rinse the basket, reassemble the layers in the same bottom-to-top order, and put the basket back.

To service the impeller, unplug the filter, press the sides, pull the pump housing down, free the pump as shown in the manual (the 55 impeller cover pulls off; on the 75 and 110 you lift the top clip, twist the impeller base counter-clockwise, and pull it free), and wash the impeller with water only, or a dilute vinegar-and-water solution for scale. Do not use soap. Reassemble in reverse and confirm the impeller spins freely. Replacement foam, Matrix, and MatrixCarbon packs made for Tidal are sold separately.

Orders ship in 1–2 business days, and shipping is free on orders of $35 or more. Most equipment is returnable for 365 days with free return shipping and no restocking fee. Opened chemicals, foods and medications are not returnable.

If you want help matching equipment to your tank, ask us through the contact form.

Shop filtration Filter media