How to raise alkalinity in a reef tank

How to raise alkalinity (KH) in a reef tank safely: which buffer to use for your pH, step-by-step dosing, magnesium checks and the best alkalinity test kits.

Short answer: to raise alkalinity (KH) in a reef tank, test it first, then add a reef alkalinity supplement in small steps and retest before adding more. If your pH is fine, use a product that raises alkalinity without pushing pH up, such as Seachem Reef Builder. If pH is also low, use a buffer that raises both, like Seachem Reef Buffer. If alkalinity won't rise, check magnesium and calcium before adding more buffer.

What alkalinity is and why it drops

Alkalinity (also called KH or carbonate hardness) is the water's carbonate and bicarbonate supply. It buffers pH, and corals, coralline algae and clams use it to build their skeletons. That means a growing reef uses up alkalinity every day, and natural organic acids in the tank push pH and alkalinity down too. Seachem recommends keeping reef alkalinity around 3–5 meq/L (8–14 dKH) and never letting it fall below 2 meq/L.

Which alkalinity product to use

Your situation Product What it does (manufacturer)
Alkalinity low, pH fine Seachem Reef Builder (300 g, 600 g) Raises carbonate alkalinity with minimal impact on pH. Over time it tends to stabilize pH at 8.3. Used as directed, it won't deplete calcium, magnesium or strontium.
Alkalinity and pH both low Seachem Reef Buffer (250 g, 500 g) Raises pH to 8.3 and raises carbonate alkalinity. A carbonate/bicarbonate blend with a pK of about 8.6 for reef bioloads.
Prefer a liquid buffer for pH and alkalinity Seachem Aquavitro Eight.Four Balanced liquid buffer (pK 8.6) that raises pH while adjusting alkalinity, made to hold pH in the 8.3–8.5 range.
pH low but alkalinity already fine Seachem Aquavitro Balance Raises pH by correcting the carbonate/bicarbonate ratio without affecting calcium and alkalinity. Not an alkalinity booster.

Seachem says Reef Builder and Reef Buffer can be used together. Use Reef Builder to raise alkalinity without affecting pH, and Reef Buffer when you need to raise both.

Step by step: raising alkalinity safely

  1. Test alkalinity (and pH). Write down the number so you know how far you have to go. Retest before every dose.
  2. Pick the right product from the table above, based on your pH.
  3. Dissolve it first. Seachem's directions for both Reef Builder and Reef Buffer say to dissolve the powder in at least one cup (250 mL) of fresh water before adding it to the tank. Add it to a high-flow area.
  4. Follow the label dose and its daily limit. Seachem gives a per-volume dose and a maximum per day on the label and in its dose calculator. Don't go over it to fix a low reading faster.
  5. Retest and repeat until you reach your target, then switch to maintenance dosing that matches how much your tank uses.

Don't mix alkalinity with calcium supplements

Seachem warns not to mix alkalinity supplements directly with calcium, magnesium or strontium supplements. It's best to add calcium and carbonate additives on alternate days, or at least 30 minutes apart. Seachem also warns that too much alkalinity can speed up the loss of calcium, magnesium and strontium, so more isn't better.

Alkalinity won't go up? Check magnesium

If alkalinity drops right back down, or the tank turns cloudy after dosing, the water may be out of ionic balance. Seachem's Reef Buffer directions say that if alkalinity has reached 6 meq/L without getting pH to at least 8.20, or you see cloudiness that doesn't clear within 15 minutes, the system isn't ionically balanced. To fix it, do a water change or adjust magnesium and calcium to about a 3:1 magnesium-to-calcium ratio. Test magnesium with a Salifert Magnesium Test Kit or Nyos Magnesium Test Kit. Magnesium supplements we carry include Seachem Aquavitro Ions, Tropic Marin Bio-Magnesium and Brightwell Magnesion.

Alkalinity test kits

Kit Notes
Salifert KH/Alk Test Kit A popular reef titration kit
Nyos Alkalinity Test Kit 50 tests
Tropic Marin Pro KH Test Kit For reef and marine tanks

See all kits in our test kits collection, and read how to test your aquarium water.

Long-term: keep alkalinity stable

Once you know how much alkalinity your tank uses each day, steady small additions beat big weekly corrections. Water changes with a quality reef salt also replace alkalinity (see which salt to use). Growing SPS tanks often move to a matched calcium and alkalinity system. See our guides to the Balling method and All-For-Reef.

FAQ

Does Reef Builder raise pH?

Seachem says it raises alkalinity without immediately affecting pH, and over long-term use pH tends to settle at 8.3.

Can I use Reef Builder and Reef Buffer together?

Yes, Seachem says they can be used together.

Why does my alkalinity keep dropping?

Corals and coralline algae use it to grow, so a healthy, growing reef uses alkalinity steadily. Track it and dose to match.

Shop test kits Shop saltwater