How to use an aquarium UV clarifier

Sicce’s official UV-C clarifier tank and flow figures, submerged or in-line installation, and lamp safety.

A UV-C clarifier shines short-wave ultraviolet light on water as it passes through a closed chamber. Sicce’s UV-C Clarifier is the unit this guide describes, using Sicce’s official instruction manual and US product page. Sicce designed the range “for easy and practical use in aquariums and ponds.” A separate ETL safety note in the same manual says the appliance has not been investigated for use in swimming-pool or marine areas, and Sicce also says not to use it in swimming pools or any application where people are in the water. This guide does not add reef-specific exposure times or parasite claims beyond what Sicce publishes.

What size UV sterilizer or clarifier do I need?

Quick pick from Sicce’s published table (aquarium sizes and pump flow, US units):

Tank Clarifier Pump flow through it
25–49 gal Sicce UV-C 7 W 50–130 gph
50–100 gal Sicce UV-C 7 W or Sicce UV-C 9 W 50–130 gph (7 W) / 100–200 gph (9 W)
101–150 gal Sicce UV-C 9 W 100–200 gph
151–250 gal Sicce 13 W (not sold here right now) 150–400 gph

Sicce says slower flow through the chamber increases UV-C exposure, so keep the pump inside the range for the size you pick. Details, install steps and lamp changes are below.

What you’ll need

Sicce UV-C Aquarium Clarifiers
Sicce UV-C Aquarium Clarifiers

the 7 W or 9 W model sized to your tank (the 13 W model is listed by Sicce but is not for sale in this shop right now)

From $149.99

Choose size
Sicce Syncra Silent Nano Pump

Sicce Micra

Sicce Syncra Silent Nano Pump

when those published flow rates fall inside Sicce’s table

$34.99

Sicce Pump Clean
Sicce Pump Clean

Sicce lists this, or mild soap, for cleaning the quartz sleeve

$29.99

You will also need the hose fittings packed with the clarifier, a GFCI-protected outlet, and a drip loop in the cord. Always unplug the clarifier, and any other appliances in the aquarium or pond, before you touch the water or open the unit. Never look directly at, or touch, the UV-C lamp when it is on — Sicce says that can harm eyes and skin. Use the blue indicator light to confirm the lamp is working. Never run the clarifier without water, and never lift it by the power cord.

Sicce’s published size and flow table

From the official UV-C Clarifier instruction manual (US gallons and US gph). “Suggested aquarium size” is Sicce’s range, to be used with a pump in the matching flow range.Sicce UV-C Aquarium Clarifiers - 7 WattSicce UV-C Aquarium ClarifierView product →

  • 7 W — suggested aquarium size 25–100 US gallons, with a pump of 50–130 US gph.
  • 9 W — suggested aquarium size 50–150 US gallons, with a pump of 100–200 US gph.
  • 13 W — suggested aquarium size 80–250 US gallons, with a pump of 150–400 US gph. (Sicce also publishes a larger pond range for the 13 W model.) The 13 W unit is not currently for sale here; the figures are included only so the official table is complete.

Maximum pressure in the manual is 0.3 bar. Indoor-cable length on the models Sicce lists with a 10 ft (3 m) cord is 10 ft; a 13 W outdoor version with a 20 ft cord is a different SKU. The unit is IP68 and fully submersible, and it can also be used out of the water in-line. Sicce’s US product page says it quickly connects in-line to pumps and canister filters with the supplied barb fittings, and that a safety switch automatically turns the lamp off during maintenance. The product-page guarantee is 2 years, excluding the supplied UV-C lamp.

Sicce recommends limiting flow through the clarifier because a slower flow increases exposure to UV-C and, in Sicce’s words, its effectiveness. Stay inside the published gph range rather than pushing a much larger pump through the chamber.

In-stock pumps whose published flow sits inside those ranges include the Sicce Micra (90 gph) and the Syncra Silent Nano (110 gph) for the 7 W range, and the MicraPlus (158 gph) or Syncra Silent 0.5 (185 gph) for much of the 9 W range. Those are pump flow ratings, not a Sicce-branded “UV kit”; throttle or choose a model so the flow through the clarifier stays in the table above.

How to install it

From Sicce’s English installation section. The clarifier can be immersed in a sump or pond, or used out of the water. Either sleeve can be the inlet or the outlet.

  1. Unplug everything in the aquarium or pond before you start. Handle the unit carefully: it contains a glass lamp and a quartz glass tube.
  2. Fit the hose holders supplied with the clarifier. If you do not need the smaller barb steps, Sicce says to cut those unused diameters off so they do not obstruct flow. Screw the holders on with the o-rings present and correctly seated. The supplied barb sizes in the manual are ½ in (13 mm), ¾ in (20 mm), and 1 in (25 mm).
  3. Place the clarifier so the blue indicator light is visible. For in-line use, plumb a pump (or the discharge of a canister filter) to one holder and return the other holder to the tank or sump. For submerged use, keep both connections underwater and still use the hose holders so water must pass through the chamber.
  4. Connect power only after the plumbing is finished. A bright blue light means the UV-C lamp is working. Position a drip loop in the cord, and use a GFCI-protected circuit.

Sicce rates the water temperature range at +4°C / 39.2°F to +35°C / 95°F. If temperature would drop to 0°C / 32°F or below, unplug the clarifier and empty it. For winter pond storage, Sicce says to turn it off, empty it, remove it, and store it open in a dry, sheltered place.

Lamp changes and quartz-sleeve cleaning

To keep UV-C output up, Sicce recommends changing the lamp after approximately 8,000 hours of operation, or once per year. Genuine Sicce lamps are sold by wattage; replacement lamps are not in stock in this shop at the moment, so do not treat a sold-out lamp listing as available.Sicce Pump CleanSicce Pump CleanView product →

  1. Unplug the power cord. Never look at a lamp that is still on. Sicce’s safety system is meant to shut the lamp off if the head is opened, but you should still disconnect power first.
  2. Turn the outer ring nut counter-clockwise until it stops, then lift the head out of the housing.
  3. Pull the lamp gently from its socket and install the new lamp of the same wattage the same way.
  4. To clean the quartz sleeve, after the head is off, pull the tube assembly out through the openings (or with a screwdriver, as the manual shows). Clean the outside of the sleeve with a small brush, mild soap, or Sicce Pump Clean. Reseat the assembly in the only orientation that fits, then put the head back (it also has only one entry position) and turn the ring nut clockwise to close it.

Orders ship in 1–2 business days, and shipping is free on orders of $35 or more. Most equipment is returnable for 365 days with free return shipping and no restocking fee. Opened chemicals, foods and medications are not returnable.

If you want help matching equipment to your tank, ask us through the contact form.

Shop filtration Pumps & powerheads