How to raise GH and KH in a freshwater aquarium
What GH and KH mean, how to test them, and how to raise each one safely in planted tanks, shrimp tanks and African cichlid tanks, using manufacturer doses.
Short answer: Test first, then raise each number with the right product. GH (general hardness) is mostly calcium and magnesium, so you raise it with a mineral supplement such as Seachem Equilibrium or Seachem Aquavitro Mineralize. KH (carbonate hardness, or alkalinity) is your water's buffer, so you raise it with a buffer such as Seachem Alkaline Buffer. Add these to new water at water changes, change things slowly, and retest. African cichlid keepers can use Seachem Cichlid Lake Salt for GH and Fritz Rift Lake Cichlid Buffer for KH.
GH vs KH: what's the difference?
The two numbers sound alike, but they measure different things, and one product rarely fixes both.
- GH (general hardness) is the amount of dissolved calcium and magnesium. Fritz says GH affects osmoregulation, breeding behavior and whether your water suits the fish and plants you keep.
- KH (carbonate hardness, or alkalinity) is your water's buffering capacity. Fritz calls it one of the most practically important numbers to track, because it stabilizes pH and prevents dangerous swings.
If your KH is low, pH has little buffer and can swing. GH is often low with RO or DI water, which starts with almost no minerals, or with very soft tap water. If you're chasing pH itself, see our guide on how to lower pH in an aquarium (and how to raise it).
Step 1: Test GH and KH before you add anything
Don't dose on guesswork. Test your tank water and your source water, because tap water often already has some hardness.
- Fritz 6-in-1 Test Strips read pH, nitrite, nitrate, alkalinity (KH), general hardness (GH) and chlorine from one strip. Fritz's directions are to dip for two seconds, don't shake off the excess, then read pH, GH, KH and chlorine after 15 seconds, and nitrite and nitrate after 60 seconds.
For a more precise KH reading, a liquid alkalinity kit works too; browse our test kits. Write the numbers down. Test kits use different units. Seachem notes that 1 meq/L of alkalinity equals 2.8 dKH, so divide a dKH reading by 2.8 to get meq/L. For more on testing, read testing your water: which test kits you need.
Step 2: How to raise GH
Seachem Equilibrium (powder, for planted tanks)
Seachem Equilibrium is made to set the mineral content of a planted aquarium. Seachem says it contains only calcium, magnesium and potassium salts, with no sodium or chloride, and no phosphate or nitrogen. It's well suited to RO, DI or other mineral-poor water.
- Seachem's dose: 16 g (1 tablespoon) per 80 L (20 US gallons) raises GH by 1 meq/L (3 dH). Add it when you set up a tank or to the new water at a water change.
- Mix it first. Seachem recommends mixing it with about 1 L (1 qt) of water. The mix looks white and opaque and leaves a slight haze in the tank that should clear in 15–30 minutes.
- Don't use it for top-offs. Seachem says not to add Equilibrium when replacing evaporated water. Evaporation leaves minerals behind, so dosing top-off water makes GH creep up.
- The dose is based on RO or DI water. With tap water, measure GH first and only add what you need.
Seachem gives a general target for planted tanks of about 1–2 meq/L (3–6 dH) GH, or matching your KH. Sizes: 300 g and 600 g.
Seachem Aquavitro Mineralize (liquid)
Seachem Aquavitro Mineralize is a blend of divalent salts that restores or raises GH in planted aquariums. A standard dose raises GH by 1 meq/L (2.8 dGH). Shake well, start at a reduced dose and adjust based on your test results. It comes in 150 mL, 350 mL and 1 L.
Remineralizers for RO water (shrimp tanks)
If you keep shrimp on RO water, a remineralizer rebuilds the water from zero before it goes in the tank:
- Liquid Gardens Remineralizer GH+ adds GH to RO water. It's the GH-only option.
- Liquid Gardens Remineralizer GH/KH+ adds both GH and KH to RO water.
Dissolve either one in RO water to your target before adding it to the aquarium, and follow the label dose. As a rule of thumb from shrimp keepers, GH-only minerals are the usual pick for Caridina (bee shrimp) on buffering soils, which want KH near zero. GH/KH minerals usually suit Neocaridina, such as cherry shrimp, which tolerate some KH.
Step 3: How to raise KH
Seachem Alkaline Buffer is a non-phosphate, sodium bicarbonate buffer that raises KH and pH, and holds pH between 7.2 and 8.5. Seachem designed it for planted aquariums and very hard water, where phosphate buffers could cause algae or cloudiness.
- Seachem's dose: 1 teaspoon (6 g) per 80 L (20 US gallons) daily until you reach the pH you want. Each dose raises alkalinity by about 1 meq/L (2.8 dKH).
- To hold a set pH, Seachem pairs it with Seachem Acid Buffer. Work out the Alkaline Buffer you need for your target KH first, then use Seachem's ratio chart to get the Acid Buffer amount. For example, a 2.0 to 1 ratio of Alkaline to Acid Buffer targets pH 7.0 in RO water.
Sizes: 70 g and 300 g. Fritz also recommends a minimum KH of 4 dKH (80 ppm) for nitrification when using its FritzZyme bacteria, which is one reason soft-water tanks can struggle to cycle. If you're setting up a new tank, see cycling a new tank.
African cichlids: raising GH and KH together
Malawi, Victoria and Tanganyika cichlids want much harder water than most community fish. Here the salt and the buffer do different jobs:
- Seachem Cichlid Lake Salt sets GH. It supplies calcium, magnesium, sodium and potassium, but it does not set pH or alkalinity. Seachem's doses per 40 L (10 US gallons) of RO or DI water are: Tanganyika 11 g (1.5 tsp, raises GH by 8.8 dGH), Malawi 5.5 g (3/4 tsp, 4.4 dGH) and Victoria 3.6 g (1/2 tsp, 3 dGH). Seachem's recommended GH ranges are 8–14 dGH (Tanganyika), 4–8 dGH (Malawi) and 3–6 dGH (Victoria).
- Fritz Rift Lake Cichlid Buffer is what Fritz recommends for a more significant KH increase in African cichlid systems.
Seachem says to dose the salt only for the volume of water you replace, not for evaporation top-offs, and to dissolve it in fresh water first. For food, see our guide to the best cichlid food.
Which product do you need?
| Your situation | Raise | Product |
|---|---|---|
| Planted tank on RO/DI or soft water | GH | Equilibrium or Aquavitro Mineralize |
| pH keeps dropping, KH tests low | KH | Alkaline Buffer (with Acid Buffer to hold a set pH) |
| Caridina / bee shrimp on RO water | GH only | Liquid Gardens GH+ |
| Neocaridina / cherry shrimp on RO water | GH and KH | Liquid Gardens GH/KH+ |
| African Rift Lake cichlids | GH and KH | Cichlid Lake Salt + Rift Lake Cichlid Buffer |
Tips for raising hardness safely
- Go slow. Adjust the new water at each water change rather than dumping a big dose into a tank full of fish or shrimp. Fritz advises limiting pH changes to 0.2 units per day when fish are present, and KH changes move pH.
- Treat new water, not top-off water. Seachem says not to use Equilibrium or Cichlid Lake Salt when replacing evaporated water.
- Retest after every change and keep a log, so you learn how your tap or RO water behaves.
- Make water changes part of the routine. See how to do an aquarium water change.
FAQ
Does raising KH raise pH?
Usually, yes. Seachem says Alkaline Buffer raises both pH and alkalinity. Equilibrium and Cichlid Lake Salt raise GH and aren't meant to set pH.
Can I use Equilibrium to raise KH?
No. Seachem says Equilibrium raises GH, and it recommends Alkaline Buffer to maintain KH.
What GH should a planted tank have?
Seachem's general guide is about 3–6 dH GH, or about the same as your KH. Plant needs vary, so check the species you keep.
Shop the full range in Water Care, Live Plants & Plant Care and Test Kits.
Sources: seachem.com (Equilibrium, Alkaline Buffer, Cichlid Lake Salt); fritzaquatics.com (6 in 1 Test Strips and directions); Aquarium Supply product listings.