How to use a media reactor

Two Little Fishies’ official PhosBan Reactor design, sizes, and mounting notes, and which phosphate media does not belong in a tumbling reactor.

A media reactor is a small chamber that pushes water through chemical filter media so the media is used evenly, instead of sitting in a bypass-prone bag. This guide follows Two Little Fishies’ published description of the PhosBan® Reactor 150 and Reactor 550. For flow rate, media fill height, and the first startup, use the operating instructions packed with the reactor — those figures are not repeated on Two Little Fishies’ current product pages, and this guide does not invent them. For bagged media in a regular filter, see Choosing filter media and How to use Seachem Purigen.

PhosBan Reactor 150 vs 550: which size?

Both are upflow GFO / carbon reactors that hang on the tank, sit in the sump, or run in line. Pick by tank size and how much media you want to run. Specs are Two Little Fishies’ published figures, also listed on our PhosBan Reactor page.

Reactor 150 Reactor 550
Recommended tank size Up to 150 gal Up to 600 gal
Max media capacity 200 g 750 g
Max flow rate 250 gph 700 gph
Size (L × W × H) 3.0 × 4.0 × 14.25 in 4.5 × 6.5 × 15.125 in
Clearance to hang on back 4.0 in 5.0 in
Inlet / outlet ½ in barb ½ in barb
Spare parts Foam disks · Lid o-ring · NPX adaptor (bio-pellets) · CDX adaptor

Max flow is the reactor’s limit, not the running flow for GFO. Set the running flow with the included ball valve, using the operating instructions packed with the reactor and your media’s directions. Tubing, pump and media are sold separately.

What you’ll need

Two Little Fishies PhosBan Media Reactor
Two Little Fishies PhosBan Media Reactor

the 150 or the 550, sized to the tank

From $77.18

Choose size
Two Little Fishies PhosBan Media Reactor Extension Kit

PhosBan Reactor Extension Kit

Two Little Fishies PhosBan Media Reactor Extension Kit

if you are hanging a Reactor 150 and want the flexible pipe connection Two Little Fishies sells for that installation

$4.98

Two Little Fishies PhosBan Media Reactor Replacement Foam Disks - 2-Pack

PhosBan Reactor Replacement Foam Disks

Two Little Fishies PhosBan Media Reactor Replacement Foam Disks - 2-Pack

spare disks in the 150 or 550 size, for when the originals wear out

From $3.41

Choose size
Two Little Fishies PhosBan Media Reactor Replacement O-Ring

PhosBan Reactor Replacement O-Ring

Two Little Fishies PhosBan Media Reactor Replacement O-Ring

a spare lid o-ring for the 150 or the 550

From $2.01

Choose size

Two Little Fishies designed this reactor for PhosBan® or other chemical filter media. PhosBan itself is ferric oxide hydroxide (GFO) sold by Two Little Fishies for adsorbing phosphate and silicate in saltwater and freshwater; it is described as not releasing the adsorbed substances. We do not currently list PhosBan media as a store product, so buy the media the reactor’s instructions call for from a source that carries it, and follow that media’s directions for rinse and replacement. Test phosphate (and silicate, if that is what you are targeting) so you can tell when the media is spent — see Testing your water.

Which reactor size

From Two Little Fishies’ current PhosBan Reactor product pages:Two Little Fishies PhosBan Media Reactor - 150Two Little Fishies PhosBan Media ReactorView product →

  • Reactor 150 — one reactor for aquariums up to 150 gallons.
  • Reactor 550 — one reactor for aquariums up to 600 gallons.

Both models use an upflow design: water is pushed in at the bottom, through a dispersion plate, then up through the media. Two Little Fishies says that evens out the flow and helps prevent channeling, so the media is used more efficiently. Either size can be mounted hanging on the back of the aquarium or below the aquarium. Each includes a ball valve for regulating flow and flexible connection fittings that rotate 180 degrees. The lid is threaded so you can open it for service.

How to set it up

Use the diagrams and pump recommendations in the included operating instructions for tubing size, pump size, fill height, and the first prime. The outline below stays with what Two Little Fishies publishes on the product pages, plus ordinary leak-free plumbing practice.

  1. Choose hanging-on-the-tank or below-tank mounting, as the product pages allow both. Keep the reactor upright. If you are hanging a Reactor 150 and want a more flexible pipe run, Two Little Fishies sells an extension kit for that installation.
  2. Install the fittings and ball valve that came with the reactor. The fittings rotate 180 degrees so you can line the hose up with your pump and return. Seat the lid o-ring cleanly before you thread the lid on.
  3. Rinse and load the chemical media the way that media’s manufacturer directs, and use the foam disks (or the screens supplied for the media you are running) so media cannot wash out. Do not invent a fill height — use the height or weight in the reactor’s operating instructions and on the media package.
  4. Plumb a pump to feed the reactor and return the outlet to the tank or sump, following the included instructions for pump size and for how to prime and purge the first dusty water. Use the included ball valve to regulate flow once the reactor is running.
  5. Watch for leaks at the lid and fittings after startup. If an o-ring is flattened or nicked, replace it with the matching 150 or 550 o-ring. Replace worn foam disks rather than running the reactor without a retainer.

What not to put in a tumbling reactor

Not every phosphate media is meant to tumble. Seachem’s directions for Seachem PhosGuard say to use it in a bag with good flow, but not so much flow that the beads tumble against each other, and Seachem does not recommend it in a tumbling media reactor because that can make dust. If phosphate is the goal and you would rather use PhosGuard, keep it in a bag in a filter, not in a fluidized PhosBan Reactor, and follow the PhosGuard notes in our Purigen guide.Seachem PhosGuard 100 mLSeachem PhosGuardView product →

Two Little Fishies also sells a PhosBan Reactor NPX adaptor and NPX screens for running bio-plastics in the same body, and a CDX adaptor that ties the reactor to a protein skimmer’s airline. Those are different uses than a simple GFO upflow. If you go that route, use Two Little Fishies’ directions for that adaptor and media. This guide does not add biopellet or carbon-dosing steps.

When phosphate (or silicate) stops dropping or starts to climb again, replace the spent media and rinse the reactor and disks. Do not leave exhausted GFO in the chamber just because the reactor is still flowing.

Orders ship in 1–2 business days, and shipping is free on orders of $35 or more. Most equipment is returnable for 365 days with free return shipping and no restocking fee. Opened chemicals, foods and medications are not returnable.

If you want help matching equipment to your tank, ask us through the contact form.

Shop filtration Filter media Shop Two Little Fishies